Phoenix Metro
Construction Electrical in Phoenix.
- (480) 771-3252
- Serving the entire Phoenix metro — we come to you
- Office: Mon–Fri 8:00 AM – 5:00 PM · 24/7 emergency service
- 2-year workmanship warranty · 1-year parts warranty
- Veteran-owned & operated · residential + commercial
- 73 five-star Google reviews
Construction electrical is calendar work. On a remodel or an addition, the electrician shows up twice, rough-in and finish, and both appearances have to land on someone else’s schedule. Miss the rough-in date and drywall waits. Fail the inspection and everything behind it slides. The trade is wiring; the job is sequencing. Good construction electricians get judged less by their splices, which any inspector can check, than by their calendars, which every other trade depends on.
This page covers construction electrical across the Phoenix metro: kitchen and bath remodels, additions, garage conversions, casitas and ADUs, and light-commercial tenant improvements. Whether we are working inside a general contractor’s schedule or running the electrical scope directly for an owner, the promise is the same: bid from the plans, hit the dates, stage clean for inspection, and keep the paper trail lenders and inspectors want. The work sits inside our electrical division, licensed CR-11 under ROC #363423.
What this work involves
Construction electrical is phase work, and every phase has a gate. Temporary power lets the other trades work. Rough-in puts boxes, home runs, and conduit into open framing. The rough inspection closes the walls. Finish brings devices, fixtures, and panel makeup after paint. The final inspection closes the permit, and the close-out packet closes the file. Run in order, none of it is dramatic. Run out of order, every step costs twice: once to do, and once to undo whatever sealed it in.
What we need from you or your GC is simple: plans if they exist, a walkthrough if they do not, and a real schedule we can commit against. Plans do not need to be fancy; they need to be decided, because wire follows decisions and re-follows changed ones at a price. Here is the full phase scope:
Circuit counts, panel capacity, and service size checked against the plan, with documented load calculations for permits, utilities, and lenders.
Safe, code-legal temporary power staged early so the site never waits on an extension cord.
Boxes, home runs, and conduit set after framing and coordinated with plumbing and mechanical, so the trades stack instead of colliding.
Supported, protected, labeled, and nail-plated before the inspector arrives, so the rough inspection is a formality instead of a delay.
Devices, fixtures, fans, and panel termination after paint, with every circuit tested rather than assumed.
Permit sign-offs and the written record that owners, lenders, landlords, and future buyers eventually ask for.
General Construction Electrical pricing in Phoenix
Construction scopes are priced flat-rate and in writing, phase by phase, after we have seen the plans or walked the space. That structure protects both sides: the GC gets numbers that hold across the schedule, and the owner sees exactly what each phase includes before committing to any of it. Phase pricing also makes the bid comparable: you can see what rough-in, finish, and close-out each carry instead of staring at one opaque number.
What moves a construction bid:
| Cost factor | Why it matters |
|---|---|
| Plan completeness | A dimensioned plan bids tight; a sketch bids with allowances, and we tell you which one you handed us. |
| Scope size | Opening counts, circuit counts, and whether the service or panel changes as part of the project. |
| Construction type | Block exterior walls, slab floors, and attic-only routing change the labor compared to open frame construction. |
| Phasing and mobilizations | One continuous run prices differently than staged visits matched to a GC calendar across weeks. |
| Permit and inspection path | City versus county process, the inspection count for the scope, and utility coordination when the service changes. |
The 10% military, veteran, and first-responder discount applies, and finished work carries our 2-year written workmanship warranty with 1-year manufacturer coverage on parts.
The Arizona-specific part
Phoenix construction habits shape the electrical plan before anyone pulls wire. Most of the housing stock is slab-on-grade with block exterior walls, so wiring lives in attics and interior frame walls, and remodel routing gets planned around masonry instead of through it. That attic reality has a seasonal edge: summer attic work is brutal, and on occupied remodels we plan rough-in phases with the season in mind, which is one more reason early scheduling beats heroic scheduling.
The project mix is local too. Casitas and ADUs are having a moment across the Valley, and each one is a feeder, a subpanel, and a load calculation against the existing service. Additions routinely land on 1980s and 1990s panels already at capacity age, and the load letter answers whether the panel rides along or gets upgraded as part of the project. Remodeled spaces also get held to current code: AFCI and GFCI protection lands in the remodeled rooms even when the rest of the house predates it, and inspectors check.
Permits are a patchwork worth respecting. Each city runs its own process, unincorporated areas like San Tan Valley and the Sun City area route through the county, and service changes bring the utility, APS, SRP, or Mesa’s city utility, into the schedule with rules of its own. We state the permit path in writing and run the inspection calendar so nobody else on the project has to learn it mid-build.
Light-commercial tenant improvements follow the same logic with different paperwork: landlord work rules, building access windows, and commercial inspection scheduling. The discipline of staging clean for inspection matters even more there, because a lease commencement date is usually attached to the outcome.
How we run the job
We bid from plans when they exist and from a walkthrough when they do not, and the bid comes back as a phased, written, flat-rate scope with the permit call stated. Rough-in gets booked against the framing date, and when the framing date moves, ours moves with it, communicated instead of discovered.
Working under a GC
We behave like a trade partner: bid from the plans, flag conflicts early, show up on the mobilization dates, coordinate box placement with plumbing and mechanical at rough, and stage for inspection so the schedule never waits on us. Change orders route through the GC in writing, and our paperwork feeds the project file instead of complicating it.
Working directly for an owner
We translate. You get the phase plan in plain language, honest sequencing around your drywall and paint, and a clear list of the decisions only you can make: fixture counts, switch locations, where the patio outlet goes. The permit and inspection choreography stays our problem, not your crash course.
On site, we stage for inspection as if the inspector were the customer: supported runs, protected penetrations, labeled home runs, boxes at spec. After the rough passes, we step out until paint, then finish, test every device and fixture, and close the permit. Changes along the way get priced in writing before the work happens, never reconstructed afterward. You will not chase us for updates; schedule changes and inspection results get communicated the day they happen. The close-out packet, permit records and warranty terms, goes in the file, and the 2-year workmanship warranty starts. Project inquiries run through the contact page, and we run this work metro-wide; the service areas page shows the map in city terms.
General Construction Electrical FAQs
Do you work with general contractors?
Yes, constantly. We bid from your plans, commit to dates, coordinate with your other trades at rough, and stage for inspection so your schedule holds. You get one point of contact and phase pricing that does not wobble between mobilizations. Send plans and the schedule; the bid comes back phase-priced so it drops straight into your budget format.
Can you handle just the electrical on my remodel?
Yes. Owner-run remodels are common here, and we slot in as the electrical trade: scope in writing, permit handled, rough and finish coordinated around your drywall and paint dates. We stay in our lane and tell you clearly what that lane includes. If you already have other trades lined up, we coordinate directly with them rather than routing every question through you.
Do you do tenant improvements?
Yes. Light-commercial TI is part of the construction scope: suite build-outs, added circuits, lighting, and punch-list electrical, run inside landlord rules, building access windows, and the city’s commercial permit process. Punch-list-only engagements are fine too; finishing a job someone else left nearly done is normal TI work.
When should the electrician get involved in the project?
At the plan stage, before the permit is filed. Capacity questions, panel location, and circuit counts are cheap to answer on paper and expensive to answer after drywall. An early pass through the plans routinely saves a schedule from mid-build improvisation. It also keeps the panel conversation from happening mid-build, which is the expensive time to have it.
What is a load letter and who wants it?
A documented calculation showing the service and panel can carry the finished project. Utilities want it when the service changes, lenders want it in construction files, and inspectors want the math behind the permit. We produce it as part of the plan check. It is a short document that prevents long arguments.
What happens at the rough-in inspection?
The inspector checks the work that is about to be hidden: box placement, routing, support, protection plates, and connections, before insulation and drywall close it in. We stage so it passes the first time, because a failed rough does not just cost a re-visit; it stalls every trade scheduled behind us.
Can you add a subpanel for a casita or ADU?
Yes, it is standard casework in the Valley now: feeder sizing, subpanel placement, a load calculation against the existing service, and the permit that goes with it. If the main service needs help first, the load letter says so before anything gets built. Detached buildings usually want feeders sized with spare capacity, because shops and casitas only ever grow their loads.
What if the design changes mid-build?
Changes get scoped and priced in writing before the work happens. Mid-build improvisation without paper is how projects end in disputes, so we keep the change-order discipline boring: what changed, what it costs, approved in writing, then built. Small changes stay small when they are caught at rough; the goal of the discipline is speed, not bureaucracy.
Do you provide temporary power?
Yes. Code-legal temporary power is staged early so the site never waits on it, and it comes down cleanly once permanent power is inspected and live. It is part of the phase plan rather than an afterthought. On occupied remodels, temporary arrangements keep the lived-in parts of the house powered while circuits move.
Permits and inspections
Most repairs are ordinary service work; bigger scopes can involve city permitting. We perform our work to code, pull the permits our scope requires, and put what we did in writing.
What's covered
Workmanship is covered for two full years, in writing, and repair parts carry a 1-year manufacturer parts warranty — we document installs and repairs so those claims stay simple to make
Why a licensed electrical contractor matters.
Phoenix metro: Most days a tech is already working somewhere in the Valley, so same-day appointments happen when the schedule allows. After-hours emergencies are dispatched when a licensed tech is available — a real person answers and tells you the ETA on the call.
Call (480) 771-3252Request an estimate.
No pressure, no door knockers. We look at the electrical, tell you what it needs (and what it doesn’t), and put the number in writing.